čidlo/a klepání

[Gardelone]

Ciaooo Všem...!!! Měnil už někdo čidla klepání na Bussu resp. V6 TB? Mohl by mi prosím poskytnout nějaký postup? Nebo nějaká fota? Ta čidla jsou na obou stranách motoru pod trubkou vody mezi hlavama, že?!

[.mycTD]

Mám tu postup pro 166 V6TB:

flywheel side knock sensor

2010618_flywheel_side.jpg (23.94 KiB) Zobrazeno 4943 krát

Removing

Make sure that the ignition is off (STOP position), then disconnect the negative battery terminal (refer to op. 5530B10 battery - r+r ).

- 7055B54 under-engine guard - r r .

- 7040D12 engine front side cover (one) lh or rh - r r (left).

- 7040D14 engine bay rear side cover (one) lh or rh - r r (left).

- 1048B44 heat exchanger/manifold pipe - r r .

- 1088C40 thermostat- r + r .

- 1088C36 thermostat support - r + r .

- 7055B39 front additional wheel arch half (one), lh or rh, front element - r r .

- 1088D26 rigid intake pipe to water pump - r+r for versions with a/c .

1. Undo the bolt (1a) and remove the flywheel side knock sensor (1b).

Refitting ( Removing )
Fit the flywheel side knock sensor and fix it tightening the bolt to the recommended torque.

- 1088D26 rigid intake pipe to water pump - r+r for versions with a/c .

- 7055B39 front additional wheel arch half (one), lh or rh, front element - r r .

- 1088C36 thermostat support - r + r .

- 1088C40 thermostat- r + r .

- 1048B44 heat exchanger/manifold pipe - r r .

- 7040D14 engine bay rear side cover (one) lh or rh - r r (left).

- 7040D12 engine front side cover (one) lh or rh - r r (left).

- 7055B54 under-engine guard - r r .

Connect the negative (-) battery terminal.

[.mycTD]

timing side knock sensor

2010619_timing_side.jpg (25.91 KiB) Zobrazeno 4943 krát

Removing

Make sure that the ignition is off (STOP position), then disconnect the negative battery terminal (refer to op. 5530B10 battery - r+r ).

- 7055B54 under-engine guard - r r .

- 7040D12 engine front side cover (one) lh or rh - r r (left).

- 7040D14 engine bay rear side cover (one) lh or rh - r r (left).

- 1048B44 heat exchanger/manifold pipe - r r .

- 1088C40 thermostat- r + r .

- 1088C36 thermostat support - r + r .

- 7055B39 front additional wheel arch half (one), lh or rh, front element - r r .

- 1088D26 rigid intake pipe to water pump - r+r for versions with a/c .

- 1072B42 left hand or right hand inlet manifold (one) - r+r .

- 1072B12 intake manifold (one) lh or rh - r r and replace gasket (right)

1. Undo the bolt (1a) and remove the timing side knock sensor (1b).

Refitting ( Removing )
Fit the timing side knock sensor and fix it tightening the bolt to the recommended torque.

- 1072B12 intake manifold (one) lh or rh - r r and replace gasket (right)

- 1072B42 left hand or right hand inlet manifold (one) - r+r .

- 1088D26 rigid intake pipe to water pump - r+r for versions with a/c .

- 7055B39 front additional wheel arch half (one), lh or rh, front element - r r .

- 1088C36 thermostat support - r + r .

- 1088C40 thermostat- r + r .

- 1048B44 heat exchanger/manifold pipe - r r .

- 7040D14 engine bay rear side cover (one) lh or rh - r r (left).

- 7040D12 engine front side cover (one) lh or rh - r r (left).

- 7055B54 under-engine guard - r r .

Connect the negative (-) battery terminal.

[crashta]

vedle* to resil Franik na 156 2,5V6...

[Gardelone]

-> .mycTD: Díkyyy

-> crashta: Nenašel jsem... Asik jsem slepej..

[crashta]

http://www.alfisti.cz/forum/viewtopic.php?f=40&t=5479&hilit=klep%C3%A1n%C3%AD
bejvaly tam i obrazky...

[A.J.Michal]

cosik mi rika, ze obrazky by meli do 24.6 jít. Teda Kubas cosik sliboval ze bude novy hosting drive nez predstaveni nove Giu